Plumbing 101: A Necessity for Bathtub Installation
Book Appointment NowWhat are your thoughts about How to Install a Bathtub Yourself?
Mounting a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably tough job. If the old bathtub is easily available, the task can relocate quickly; if you need to open a wall surface to eliminate the old tub and position the brand-new tub, the task is much harder. In either case, the job is within a home handyman's skills, although you will certainly require a helper to move out the old tub and also embeded in the new one. Make certain you have actually certified on your own for the task as well as fit trying it. As opposed to hiring a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly assist you set up a brand-new tub in your bathroom if you have currently bought a brand-new tub as well as don't need to transform the plan of your previous water supply pipes.
Your tools as well as product list need to make up the following:
Planning for the Setup
Firstly, the supporting frame provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to avoid pressure on the bath tub.
Fit the versatile faucet adapters to the bottom of both taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you use every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you must do is detach the water system. After doing so, turn on the taps to drain any kind of water staying in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted gain access to that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the bath tub in the required placement. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bath tub up until the level reviews level.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the water supply and also examine all joints as well as new pipework for leaks as well as tighten them if necessary. Fill the bath tub as well as also inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's user's manual. Tiling and securing around the tub must wait until the tub has actually been used at least once as this will resolve it into its final setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin ensuring that the washing machines are in area between the tap and also the sink. Secure the tap in position with the manufacturer supplied backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind must be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a stiff seal, creating the water to pass through the wall surface between the bathroom as well as the tiling, bring about problems with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and also are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched paper or soft rope. Remember to constantly load the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealant can crack rather early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily offered on the market. It is suggested to fit the floor tiles using waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that report on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a good friend on another domain. Sharing is good. Helping others is fun. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Immediate response? Call.